Products

This is a complete rebuilt kit for the front of your Raptor 660 swingarm by Vito's Performance All brand new, ready to install in any year; You get all 18 required pieces: 2 Needle Bearings...

This is a BRAND NEW rear Yamaha Banshee hydraulic disc brake rotor & hub kit from Vito's Performance Will fit on any year Yamaha Banshee 1987-2006 (or Blaster 2004-2006) Also includes 4 mounting bolts.

This Is a Stainless Steel Rear Rotor by Vito's PerformanceThese Have Built in Cooling Channel Slots to Help Prolong the Life of Your Pads and Rotor, and Prevent Rotor Warping.

This Is a Complete Brand New Yamaha Banshee Rear End Assembly from Vito's PerformanceLooks Awesome, Will Fit Any Year Banshee 1987-2006Includes the Following, All New Parts:Vito's +2" Extended Axle - Heat Treated for StrengthVito's 2...

This is a BRAND NEW rear shock for a Yamaha Banshee This is calibrated right out of the box, and bolt mount right up, without any adjustments This is fully adjustable to your liking, riding...

This Is a Brand New Vito's Performance Billet Aluminum Gas CapThis Was Custom Machined, and Looks Very Nice!Includes a One Way Vent Hose with Billet End Cap That Only Allows Air to Enter the Fuel...

This is a set of 8 RED Yamaha Banshee clutch cushions by UPP Racing These pucks go inside the clutch gear, to help reduce the stress of engagement of "dropping the clutch" If you basket/gear...

This is a pair of 2 Yamaha Banshee reed spacers - these are 5/16 thick,roughly 3/8" with the gaskets These go right up against the cylinders and the carb boots. Includes all 8 allen head...

CY240 Repair-Sleeve With Triple Exhaust - Fits Vitos Cy240 Cylinder Kit Only

This is a BRAND NEW electrical Stator, ADAPTOR for a Yamaha Banshee.  This adapts your new style SQUARE PLUG stator, and allows you to use it on an older ROUND PLUG wiring harness Will fit any...

This bolt set includes 2 bolts, 2 washers, and 2 nuts (carrier not included, but shown  in photos for reference) These are the bolts and nuts that go through the bearing carrier and hold the...

This is a brand new 9 piece Yamaha Banshee swingarm bearing kit by Vitos Performance Comes complete with pivot tube, 2 x needle bearings, 2 x dust seals, 2 washers, and 2 x dust caps...

This is a complete swingarm bearing & seal rebuilt kit for the front of your Yamaha YFZ450 rear swingarm by Vito's Performance All brand new, ready to install in any year, 2004-2009 (carb models), and...

This is a BRAND NEW swingarm bearing carrier SPACER TUBE for a Yamaha Banshee or Yamaha Raptor 660 This is the piece that the axle slides through inside the rear bearing carrier replaces oem Yamaha...

This is a brand new Yamaha Blaster swingarm bearing kit by Vitos Performance 14 piece kit contains: 2 Needle Bearings 4 Seals 2 Sleeves 2 Bushings 2 Caps All necessary washers/spacers Equivalent to All Balls...

This Is a Brand New 1988-2001 Yamaha Blaster Headlight On/off Switch.This Is What Goes on the Handlebars to Select the Run Postilion, as Well and Turn on the Headlights, High and Low BeamsFits 1988-2001 Yamaha...

Works on the Stock Factory Oem Mikuni Carburetors That Has Had the Tors Removed (Will Not Work with Stock T.o.r.s.)These Will Fit Any Year Yamaha Banshee 1987-2006This Is for the Thumb Throttle Setup, and Will...

This Is a Set of 4 Replacement Rubber Boots (Dust Covers) for the Inner or Outer Tie Rod Ball Joints.Also Includes the Mounting Rings, Since the Old Ones Usually Bend When You Take Them Off.

This is ONE replacement rubber BOOT (dust cover) for either the inner or outer tie rod ball joints. Also includes the mounting rings, since the old ones usually bend when you take them off In...

This is a BRAND NEW chain guide for the REAR of a Tyson Racing swingarm

This Kit Includes a Vito's Performance Billet Aluminum Impeller and a Vito's Billet Aluminum Gear Kit (Gear, Clip. Washer, and Pin)This Kit Includes a Brand New Aftermarket High Flow Billet Aluminum Yamaha Banshee Coolant Impeller.

These Will Fit an Oem Banshee Swingarm, or Any Style Tyson Racing Swingarm.

This is a BRAND NEW Yamaha Banshee upper a-arm bushing replacement kit

This is a pair of 2 Yamaha Banshee tie rods ends. These go on the end of the tie rods, one one each side (one left hand one right hand). These are brand new aftermarket,...

This is a BRAND NEW set of O-rings and gaskets by VITO'S PERFORMANCE These replace the old ones on your aftermarket TRINITY STAGE IV 2 into 1 Banshee Cool Head. Includes all gaskets and o-rings...

This is made by VITO'S PERFORMANCE and has DUAL OUTPUTS This is a HIGH FLOW item - flows MUCH MUCH faster than the stock petcock A MUST HAVE for aftermarket carbs, especially if you are...

This Is a Pair of 2 Perfect Brand New Yamaha Front Banshee or Warrior Push Bar Bumper Rubber End Caps. This Is What Goes on the Ends of the Oem Bumper. It's Ready to Be...

This is a BRAND NEW aftermarket shifter from Vito's Performance This steel model is BLACK, and has a durable black gloss finish Ready to install on any year Yamaha Blaster 200, 1988-2006. This is a...

This is a BRAND NEW Banshee chrome rear grab bar. EXACT same as the rear bumper guard that came on a 1987 Yamaha Banshee 350 Beautiful perfect condition, ready to install this rear bumper on...

This is a BRAND NEW Vito's Performance Yamaha Banshee carb rebuilt kit This includes everything to completely rebuild you Banshee 26mm Mikuni stock OEM carb Includes the exact items seen in the photos: bowl gasket,...

This is a BRAND NEW side cover gasket from Vito's Performance for any year EFI YFZ450R 2009-2021 Goes under the cover on the side of the engine, where the flywheel and stator are This will...

This is a NEW complete Yamaha Banshee fuel petcock for the gas tank. This is made by PINGEL and has 5/16 DUAL OUTPUTS This is a HIGH FLOW item - flows MUCH more than the...

You get one Yamaha OEM front rotor Ready to install on any year Banshee 1987-2006. They also fit : Banshee 350 - 1987-2006 Raptor 700 - 2006-2018 Raptor 660 - 2001-2005 Warrior 350 - 1988-2005...

This is a brand new Yamaha Raptor 250 YFM250r complete aftermarket high performance CAMSHAFT This is by Vito's Performance This is engineered to increase your mid-range and top end horsepower and torque. Specs: Valve Lift:...

This is a set of BRAND NEW Vito's Performance thumb throttle carburetor cable Fits any of the stock carbs setups, from any year 660 Raptor This is for the THUMB throttle setup, and will NOT...

This is a 2004 or 2005 Yamaha YFZ450 steering stem shaft Ready to install on a 2004 2005 YFZ450, 04 05 YFZ 450.

This is a BRAND NEW Vito's Performance thumb throttle carburetor cable Works on the stock factory OEM Mikuni carburetor that has had the TORS removed (Will not work with stock TORS) This will also fit...

Brand New Vito's Performance Yamaha Upper and Lower Lower A-Arm Mounting Boltkit This is a brand NEW Vito's Performance YAMAHA upper and lower lower a-arm mounting bolt kit This is the short and long bolts...

This is a BRAND NEW sprocket nut for a Yamaha Banshee This is what holds the front chain sprocket to the engine (transmission) fits year Yamaha Banshee 1987-2006. MINT SHAPE, brand new, ready to use!...

This is a BRAND NEW Vito's Performance aftermarket swingarm bearing carrier rebuild kit for a Yamaha Banshee, 660 Raptor, or Blaster These are the rear wheel bearings that the axle slides through Kit includes 2...

This is a BRAND NEW Yamaha Banshee coolant impeller clip set by Vito's Performance This kit includes a brand new impeller washer, pin, and mounting clip This is for OEM impellers, as well as aftermarket...

This Is a Genuine Forged Wiseco Blaster Piston Made for Vito's PerformanceThis Fits the 72.50 Mm Big Bore 240cc CylindersThis Piston Includes Rings, Circlips, and Wrist PinAvailable in Many Sizes, Please See Our Other Listings.

This is a set of FRONT original Yamaha Banshee fenders from Vito's Performance They are 1994 PURPLE DARK VIOLET FRONT - brand new - still in factory package This plastic set includes the front fender...

This is a BRAND NEW set of Yamaha Banshee front-end plastic kit You get both the left and the right gas tank side wrap covers, as well as the radiator        cover and...